Large 24-volt commercial vehicles and industrial platforms with 24V DC infrastructure that carry 5,000 PSI capable hose and need the maximum 325-foot reach of the HP1125 Series with automatic retraction in non-classified environments where the lighter 1/3 HP motor draw and lower cost of the -EF variant fit the installation’s duty cycle, electrical capacity, and mounting configuration. The Coxreels HP1125-4-325-EF pairs the maximum-capacity HP1125 drum with a 24V DC, 1/3 HP reversible motor (a non-explosion-proof direct-current rewind drive with powered operation in both pay-out and retraction directions, connecting to a standard 24V vehicle or equipment battery system) and direct gear drive (no chain gears engage the drum directly for quiet, smooth retraction without chain stretch or lubrication intervals). The electroless nickel plated steel 90 NPT swivel hardened for 5,000 PSI service over the brass swivel on standard 1125 models pairs with AFLAS seals for the chemical and heat resistance the high-pressure fluid path demands. A candid note on duty cycle at this drum size: the 1/3 HP motor on a fully loaded 325-foot drum operates closer to its output ceiling than on shorter drums it is the appropriate choice for lower-cycle installations with straightforward overhead mounting and minimal hose routing friction, where the battery system has sufficient capacity for the heavier startup load of the maximum-capacity drum. For high-cycle production use, significant hose routing friction, or any installation where the drum is consistently fully loaded at 325 feet throughout a production shift, the 1/2 HP -EB provides the torque margin the heavier duty demands. When in doubt at this drum size and pressure, choose the -EB.*Note: The above product image is for illustration purposes only. This product is a reel and does not include any hose. Please note this before ordering.Type: Electric Motor Rewind Hose Reel | Series: HP1125 | Motor Type: 24V DC, 1/3 HP, Non-Explosion Proof, Reversible | Drive: Direct Gear Drive (No Chain) | Hose I.D. (in.): 1/2 | Hose O.D. (in.): 7/8 | Hose Length (ft.): 325 | Hose Included: No | Max PSI: 5,000 | Max Temp (F): 250 | Swivel: Electroless Nickel Plated Steel 90 NPT | Swivel Seals: AFLASFeatures:24V DC, 1/3 HP non-explosion-proof reversible motor with direct gear drive connects directly to 24V vehicle or equipment battery systems; no AC outlet or compressed air supply required at the reelReversible motor operation powered control in both pay-out and retraction directions, enabling remote deployment and retrieval from a cab or service body switch across the full 325-foot drum capacityDirect gear drive no chain or sprocket; engages the drum directly for quiet, smooth retraction without chain slack, stretch, or lubrication requirements325-foot maximum capacity the longest single-drum reach in the HP1125 Series; suited to lower-cycle 24V installations where 5,000 PSI capability and maximum hose reach are both required and the 1/3 HP motor draw fits the vehicle’s electrical capacity and retraction duty cycleElectroless nickel plated steel 90 full-flow NPT swivel inlet hardened for 5,000 PSI service; greater pressure capability and corrosion resistance than the brass swivel on standard 1125 Series modelsAFLAS swivel seals fluoroelastomer compound with superior chemical and heat resistance over Nitrile; rated to 250F and suited to hydraulic fluid, petroleum, chemical, and high-pressure service environmentsExclusive low-profile outlet riser and open drum slot design provides a non-crimping, flat smooth hose wrap across all 325 feet of drum capacityHeavy-duty CNC robotically spun and ribbed discs with rolled edges for greater strength, durability, hose protection, and operator safetySturdy one-piece, all CNC robotically welded 12-gauge steel A-frame base not bolted for superior reel structure; mounting pattern in base for wall, vehicle-body, or ceiling installationPermanently lubricated, self-aligning pillow block bearings for trouble-free, smooth drum rotation under the full weight of a loaded 325-foot drumAdjustable tension brake prevents free-wheeling during hose deployment; long-handled locking pin secures drum during transport or storage; long-lasting chip-resistant, rust-inhibiting CPC powder coat finish; 2-year manufacturer’s limited warrantyMade in USA: 2 Year WarrantyApplications:Large commercial vehicle & transit fleet lower-cycle, high-pressure 24V extended-length service vehicles and transit maintenance facilities carrying 5,000 PSI hose where 325 feet of reach is required, retraction frequency is moderate, and the 1/3 HP motor draw suits the vehicle’s electrical budget at maximum drum capacityMobile hydraulic test & service 24V, lower frequency 24V portable test units carrying 5,000 PSI hydraulic test hose where 325-foot reach and automatic 24V retraction are both required, and the test cycle frequency is low enough that the 1/3 HP motor handles the maximum drum load without sustained thermal stressAgricultural & field service 24V, high-pressure, maximum reach 24V tractors and self-propelled service units where 5,000 PSI fluid lines and 325 feet of reach cover large facility or field service areas, and retraction occurs infrequently enough per shift to suit the 1/3 HP motor on the maximum-capacity drumLarge construction equipment service 24V, lower cycle 24V service vehicles maintaining hydraulic-heavy construction machinery at 5,000 PSI where 325-foot maximum reach reduces equipment repositioning and retraction frequency across the shift is within the 1/3 HP motor’s capability at this drum sizeFixed plant & facility with 24V DC infrastructure lower cycle large-bay maintenance stations and test facilities running 24V DC power where 5,000 PSI service lines, 325-foot hose capacity, and the non-classified environment make the -EF the appropriate lower-draw alternative to the 1/2 HP -EB for infrequent retraction useFAQs:Q: Is the 1/3 HP motor adequate for the 325-foot HP1125 drum at 5,000 PSI?A: For the right installation profile yes, with caveats. The 1/3 HP motor is adequate on the 325-foot HP1125 drum when three conditions are met simultaneously: the mounting is straightforward with minimal hose routing friction, the retraction frequency is genuinely low (infrequent cycles per shift rather than continuous production), and the 24V battery system has the capacity to handle the heavier startup current of the maximum-capacity drum without voltage drop. At 325 feet and 5,000 PSI, this is the most demanding application of a 1/3 HP motor in the HP1125 Series any deviation from these conditions pushes the motor toward the edge of its capability. The 1/2 HP -EB is the conservative choice at this drum size; the 1/3 HP -EF serves when the installation genuinely fits the lower-cycle profile and the cost or current savings of the lighter motor justify the tighter operating margin.Q: What is the difference between the HP1125-4-325-EF and the HP1125-4-325-EB?A: Both are 24V DC reversible motors on the maximum-capacity 325-foot HP1125 drum at 5,000 PSI same voltage, same pressure rating, same chassis. The -EF is 1/3 HP; the -EB is 1/2 HP. On the 325-foot drum, this difference is more consequential than on any shorter drum in the HP1125 Series: the heavier startup inertia at maximum capacity places greater demand on the motor at the beginning of every retraction cycle. The 1/2 HP -EB handles this load with headroom; the 1/3 HP -EF handles it within tolerance for low-cycle use. For high-cycle production, significant routing friction, or consistent full loading, choose the -EB. If there is any uncertainty about the duty cycle at 325-foot / 5,000 PSI, choose the -EB.Q: What is the difference between the HP1125-4-325-EF and the HP1125-4-100-EF?A: The motor is identical 24V DC, 1/3 HP, non-explosion-proof, reversible, with direct gear drive on the HP1125 5,000 PSI frame. The difference is drum capacity and physical size: the 325-foot model is approximately 31.75 inches wide versus approximately 19.75 inches wide on the 100-foot model, with a different mounting bolt pattern. The duty cycle guidance that applies to the -EF matters more at 325 feet than at 100 feet the motor has less headroom above the heavier drum load, making the low-cycle, straightforward-mounting conditions more critical to observe than on the smaller drum.Q: What is the difference between the HP1125-4-325-EF and the standard 1125-4-325-EF?A: Both use a 24V DC, 1/3 HP reversible motor on the same basic chassis with direct gear drive. The difference is working pressure and swivel specification. The HP1125-4-325-EF is rated to 5,000 PSI with an electroless nickel plated steel swivel and AFLAS seals. The standard 1125-4-325-EF is rated to 3,000 PSI with a machined brass swivel and Nitrile seals. For 24V non-classified applications at or below 3,000 PSI, the standard 1125-4-325-EF is the more economical choice; for applications requiring up to 5,000 PSI, the HP1125-4-325-EF is required.Q: Does the reel come with hose included?A: No the HP1125-4-325-EF ships less hose. The drum accepts 1/2″ ID / 7/8″ OD hose up to 325 feet. Coxreels recommends SAE 100R16 wire braid hose for HP1125 Series reels rated for hydraulic and high-pressure oil service at up to 5,000 PSI and 250F. Use assemblies with fittings rated and crimped for high-pressure service, and verify hose OD does not exceed 7/8 inch to ensure correct drum wrap. Note that a fully loaded 325-foot drum adds substantial hose weight to the reel factor this into both the mounting structure load calculation and the motor startup current demand.body{margin:0;padding:0;overflow-x:hidden;}.spec-accordion{width:100%;max-width:1100px;margin:1em auto;font-family:Verdana,Arial,sans-serif;}.spec-accordion-toggle{width:100%;display:grid;grid-template-columns:32px 1fr 32px;align-items:center;gap:8px;text-align:center;cursor:pointer;background:#444;color:#fff;border:0;padding:12px 16px;font-size:16px;font-weight:700;text-transform:uppercase;}.spec-accordion-title{grid-column:2;text-align:center;text-transform:uppercase;}.spec-accordion-icon{grid-column:3;text-align:right;font-size:20px;font-weight:700;}.spec-accordion-panel{border:1px solid #cfcfcf;border-top:0;padding:0;background:#fff;display:block;}.spec-table-wrapper{width:100%;max-width:1100px;margin:0 auto;overflow-x:auto;}.spec-table{width:100%;border-collapse:collapse;font-family:Verdana,Arial,sans-serif;font-size:12px;color:#111;}.spec-table th,.spec-table td{border:1px solid #d3d3d3;padding:6px 8px;text-align:center;vertical-align:middle;}.spec-table thead th{background:#444;color:#fff;text-transform:uppercase;font-weight:700;}.spec-table thead tr:nth-child(2) th{background:#e9e9e9;color:#111;}.spec-table tbody tr:nth-child(even){background:#f7f7f7;}.spec-table a{color:#0066cc;text-decoration:none;font-weight:700;}.spec-table a:hover{color:#004f99;text-decoration:underline;}@media(max-width:640px){ .spec-table thead{display:none;} .spec-table tbody td{display:flex;justify-content:space-between;align-items:center;border-bottom:1px solid #e2e2e2;padding:8px;} .spec-table td::before{content:attr(data-label);font-weight:700;text-transform:uppercase;flex:0 0 45%;text-align:left;color:#444;}} AVAILABLE VARIATIONS AND SPECIFICATIONS LESS HOSESKUSTANDARD CAPOPTIONAL CAP.Reducer requiredINLET SWIVEL & OUTLET RISERPSIHP SKUHP PSIAPRX. LBS.SIZE INDEXI.D.O.D.FT.I.D.O.D.FT.1125-4-3251/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-32550004831125-4-325-A1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-A50004831125-4-325-AB1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-AB50004831125-4-325-C1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-C50004831125-4-325-E1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-E50004831125-4-325-ED1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-ED50004831125-4-325-EF1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-EF50004831125-4-325-EB1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-EB50004831125-4-325-EA1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-EA50004831125-4-325-H1/2″7/8″3253/8″3/4″4501/2″ F NPT3000HP1125-4-325-H5000483const accordionToggle = document.querySelector(‘.spec-accordion-toggle’);const accordionPanel = document.querySelector(‘.spec-accordion-panel’);const icon = accordionToggle.querySelector(‘.spec-accordion-icon’);accordionToggle.addEventListener(‘click’, () => { const expanded = accordionToggle.getAttribute(‘aria-expanded’) === ‘true’; accordionToggle.setAttribute(‘aria-expanded’, !expanded); accordionPanel.style.display = expanded ? ‘none’ : ‘block’; icon.textContent = expanded ? ‘+’ : ‘?’;});Looking for more information about theCoxreelsRewindReel?Click hereto view theCatalog.For help choosing the correctCoxreelsRewindReels, please call(800) 608-5210or [email protected]
-20%
